Indy Total Construction

Terraces and patios have been very popular spaces for the outside of the home. Whether it is in the form of rooftop alcoves or Parisian courtyards, only sunrooms and porches have the potential to compete against such paved retreats. Or, at least, that’s what a recent reader survey has told us. Here are some patio surface types that exist today:

1. Patio Stones
Patio stones are sometimes also known as slabs or flags and are flat concrete blocks either in rectangular or square shapes. A lot of home builders, as well as homeowners, choose this popular type of patio surface because they are cheap and very easy to install. Although in the past, this type of patio surface was only available in grey, a wide color range is now available.

Pick colors that mesh well with your house or garden, or construct a floor patterned with dual colors. This type of patio surface looks best when matched with contrasting material, such as bricks, landscape rocks, cedar, rot-resistant wood, or aluminum. Patio stones can also be found in various surface textures, such as those that come with aggregates that are exposed. Their consistent kind of thickness is what makes them easy to install, but they are typically more expensive than normal stones.

2. Flagstone
Flagstone is a natural material which is only available when local resources have them. Flagstone is normally cut in regular lengths and widths, but how thick the piece is depends on the cutting and the stone. The change in thickness seems to make this kind of material harder to install, though. Natural flagstone pieces tend to cost more than patio stones that are manufactured.

A lot of the time, flagstone is considered artistic paving since these broken stone pieces are usually set in very random yet attractive patterns. However, flagstone is quite difficult to set the right way since a patio’s mortar joints tend to be weak and these pieces of stone need to be set tight together. Professional installers should be able to break the stones by hitting pieces of pipe or rebar that have been placed on the proper break line.

3. Bricks
One very popular type of material for building for terraces and patios are bricks. Brick colors are either in yellow or red (though there are more variations available nowadays). Choosing bricks for your outside space is really a very personal choice, though weather conditions may also play a part. If your house is situated somewhere cold, it is important to get bricks made for severe weather so they won’t crack no matter how cold or how heavy the snow falls. These are more expensive compared to hot or moderate weather bricks.

No matter which kind surface you opt for, it is important to invest a significant amount of time deciding on a design which fits in with the rest of your property.

An important consideration when building an extension is the position of any drainage pipe run — either an existing one from the house or any new waste pipes from fittings in the new extension. You must sort out the route the pipes will take before the walls are built since they will pass through them below floor level, and openings must be left in the walls as they are built.

Lintels will need to be incorporated to support the wall above the openings. If the extension is to have trench-fill foundations, ducts should be made in the concrete to allow the passage of pipes. A simple method is to set slightly larger pipes in the concrete as it is poured and then run the pipes through these round openings later.

The positions of the inner and outer leaves of the walls should be marked centrally on the concrete of the foundations with chalk. The center lines of the wall and foundations being within lin of each other.

As the walls are built, stringlines are stretched between the corners to make sure each course of bricks or blocks is laid in a straight line.

Although you can use brick for both inner and outer leaves of the wall, in practice it makes more sense to use lightweight concrete blocks for the former since these will provide a certain amount of insulation — a requirement of the Building Regulations.

With this type of construction, the inner leaf is the load-bearing part of the wall, carrying the weight of any floors and ceilings so lintels must be fitted across doorways and windows. Steel boot lintels are best since they are relatively lightweight and their shape ensures that any water that penetrates the outer leaf of the wall is prevented from reaching the inner leaf and is channeled out over the toe of the boot.

The two leaves of the wall should be constructed simultaneously, laying a few courses of each at a time. As construction proceeds, the two leaves must be linked together with metal or plastic wall ties to prevent them leaning away from each other.

Ties are designed to prevent water running across them to the inner leaf but they must still be set in the mortar joints so that they slope downwards slightly towards the outer leaf. Ties should be set about 18in apart vertically and 3ft apart horizontally, the positions in each horizontal row being staggered with those above and below. At door and window openings, ties should be set one above the other at 12in intervals.

Water penetration must also be prevented from below and this is achieved by inserting a flexible bitumen damp-proof course (DPC) in a horizontal mortar joint around the base of each leaf, at least two courses of bricks above ground level.

When the floor is laid, a damp-proof membrane (DPM) is taken up the walls and tucked under the DPC. Strips of DPC must be fitted in the vertical mortar joints where the inner leaf is turned to close off the cavity at windows and door openings, and below the threshold of the door, linking to the DPC in the outer leaf.

The walls must be toothed into the existing house walls at alternate courses to ensure permanent stability.

Having set the new lintel in place and re-finished the brickwork of the inner leaf above it, you can cut out the brickwork at the sides of the opening and, if necessary, across the base. First, draw the outline of the new opening on both sides of the wall, making it about lin wider and deeper than the actual frame dimensions to give a fitting tolerance.

External walls comprise two layers of bricks; each layer should be treated separately, working in from each side of the wall.

If the wall is a solid one produce a square edge along the opening outline on the inner layer by cutting through bricks where necessary. Always remove complete bricks even if they project beyond the outline. This gives a toothed effect to the edge.

If the base outline runs through the center of a course of bricks, remove the course completely; you can make up the difference later.

Replace the outer layer at the sides of the opening by mortaring cut bricks into the toothed sections so that their cut ends are innermost.

Next, replace the area of wall above the window, laying the bricks on the lintel and copying the original brickwork bond for strength and appearance. In a solid wall, you can create a curved, self-supporting soldier arch by setting a wooden framework in the opening on which the bricks of the arch are laid. Then the surrounding courses are fitted round the arch and the mortar left to set for a couple of days before removal of the formwork.

The frame must sit squarely in the opening; if it is twisted, you may have problems in opening and closing the window and the glass will be under stress and may shatter at the slightest vibration.

In a solid wall you can set the frame: flush with the outer face with its sill overhanging the edge; in the center of the opening with narrow reveals on each side; or flush with the inner face with a sub-sill at the bottom to throw water clear of the wall.

When the frame is set forward in the opening, the sides and top of the reveal are plastered and a wooden or tiled window board set across the bottom. When set at the back, it is normal to trim around the inside of the frame with molding

The simplest method of securing the frame is with frame fixings, a hefty screw and long plastic wall plug, but you can also use conventional wallplugs and screws, wooden wedges or metal frame ties. With each type, wedge the frame in the opening with wood offcuts so that it is set squarely in place, while the fixings are marked and made.

With screws and plugs, clearance holes must first be drilled in the frame and the hole positions on the wall marked through these. The holes are drilled and plugged and the frame fitted.

Wooden wedges are tapped into slots cut in the mortar joints and the frame nailed to the wedges. Metal frame ties also fit into slots in the joints, being screwed to the frame and mortared in place.

In all cases, you must leave a’/sin gap between the top of the frame and the underside of the lintel to allow for any settlement of the structure.

Leave the packing pieces in place. and fill the gaps at the sides with mortar, leaving it about 1/sin below the level of the frame face. Fill this gap with caulk when the mortar has set. Use caulking to fill the gap between the lintel and frame also. If there is a gap below the frame, fill this with bricks and mortar, splitting the bricks lengthways if necessary.

Make a sub-sill from wood screwed or nailed in place, or a double layer of tiles set on a sloping bed of mortar.

Another way is to cast a concrete sill in situ, making up a wooden formwork “tray” nailed to the wall. The sill should overlap the edge of the bricks by no more than in and you can form a drip channel (to prevent rainwater trickling under the sill) along the bottom edge by pinning a length of waxed cord (sash window cord will do) in the bottom of_ the tray. The top of the lintel should slope downwards so angle the sides for this. Also provide reinforcement by setting steel rods in holes drilled in the brickwork.

Mix the concrete from 4 parts sand: 1 part cement and pour it into the form. Agitate the mix to compact it and remove air bubbles and draw it off level with the top of the form. Leave the concrete for at least 24 hours before removing the foiinwork.

The frame fixing is much simpler to use and is ideal for securing wooden members to masonry. It comprises a hefty screw and a long plastic wallplug.

To use, wedge the frame in its opening and drill holes for the fixings right through it and into the wall. Without removing the frame, tap the plug and screw combination through the frame and into the wall, finally tightening the screw for a secure fixing.

Frame fixings are supplied in various lengths to hold wood thicknesses up to 33/sin. Another development of this is the hammer fixing, which is used in the same way, but set by driving a ridged, countersunk pin into the expanding plug.

With the wall above the window opening supported by stout wooden needles and adjustable jacks, and the old window frame taken out you can remove the old lintel and brickwork from above the opening.

Remove the bricks from the outer layer first. These may be laid in horizontal courses across the lintel or they may be set vertically. If the house is old, they may form a self-supporting segmental arch.

Cut through the mortar joints with a bricklayer’s chisel to remove the bricks, making a gradually tapering, stepped opening up to the level of the wooden needle above. This will prevent any brickwork from falling while working on the opening.

Removing the bricks from the outer leaf of the wall will expose the face of the load bearing lintel set in the inner leaf. You should remove this next.

From inside the house, hack off the plaster above the window opening to expose the inner face of the lintel and the brickwork above it. Again, cut out the bricks to foam a stepped opening up to the level of the needle. Then cut into the mortar joints at each end of the lintel, working along the top, ends and underneath. Use a stout bar to lever the ends of the lintel upwards to finally release them. Then get some help to lift the lintel from its bearings in the wall.

the thickness of the wall. It may lodge and form a bridge for moisture to cross from the outer skin to the inner and cause damp patches on the inner wall.

Measure up the new lintel and draw its outline on the inside of the wall centered over the new window position. Remember, the new lintel should be at least 6in wider at each side of the window opening to provide decent-sized bearings. Also, allow an extra lin at each end and on the depth to provide enough space to manoeuvre the lintel into position.

Cut straight down through the plaster along the outline with the bricklayer’s chisel to provide a cutting guide and then hack off the plaster within the outline.

Go on to remove the bricks exposed by the removal of the plaster, again cutting through the mortar joints in an effort to keep as many bricks in one piece as possible. Clean up the bearing openings and make sure their surfaces are flat and level.

Whether you are using a steel or concrete lintel, you will need some help to lift it into place.

Trowel a layer of mortar onto each bearing and lift the lintel into place, setting it centrally over the opening. Check that the lintel is flush with the inner face and outer layer of the wall.

Hold a level against the underside of the lintel and check that it is horizontal. If necessary, correct this by packing pieces of tile or slate beneath the ends. When level, fill the gaps round the ends of the lintel with more mortar and brick offcuts, pointing the joints neatly flush with the surrounding brickwork.

The positioning and installation of external doors is subject to the requirements of your local building code, so make the necessary applications to your local building department first.

Temporary support for the wall must be provided by Sin sq needles on top of adjustable metal props. To fit the needles, remove a whole brick from the outer layer and drill through the inner layer at the corners of the opening. Use the holes as a guide for cutting out the masonry from the inner layer. Insert the needles and tighten the props.

Draw the outline of the lintel on the inside wall and cut out the plaster and masonry from within. Drill the corners of the outer layer and remove the masonry. Fit the lintel on mortar bearings packed out with tiles or slates to set it level. Fill all round the inner portion of the lintel with mortar and rebuild any brickwork above it. Similarly rebuild the outer brickwork in the existing bond or stand the bricks on end to form a “sodier” arch.

When the mortar has set, remove the needles and brick up the holes. Then cut out the opening for the door frame — to fit the size of the frame.

Remove the bricks down to floor level, cutting through the protrud-bricks of the inner layer, on solid walls but removing whole bricks from the outer layer to give a toothed appearance. Square up the toothed outer layer by fitting cut bricks in place so that their “finished” ends are outermost.

Toe-nail the frame together before inserting it in the opening. Tack a length of flashing material to the underside of the sill, covering the nail heads with a bituminous sealant.

Fix the frame in the opening with screws and wallplugs, packing the sides to make them vertical. Fill gaps on the inside with mortar; apply caulking around the frame on the outside to keep out water.

The door sill should overhang the brickwork slightly and is best fitted with a metal weather bar, which is set in caulk. Once the frame is in place, hang the door and finish.

There are two methods you can use for blocking off a redundant doorway: you can fit a wood framework around the inside and panel it with wallboard on both sides, or you can use bricks or lightweight building blocks if the floor is solid. In each case, plaster is used to finish it off.

Alternatively, consider whether you can put it to some other use such as paneling in the back and filling the recess with shelves.

Removing the old frame

To remove the old door and frame, unscrew the door hinges, lift the door away and lever off the molding. The lining frame may be fixed by masonry nails, screws or metal ties cemented into the brickwork. You should be able to lever it free, but if not, cut through its fixings by working a saw blade between the back of the frame and the wall.

Paneling with wallboard

If you are filling an opening in a stud partition, the supporting framework should be made of wood to match the framework of the partition — usually 2 x 3 or 4in lumber. On the other hand, if paneling a masonry wall, you might need two separate frames of something like 2in sq wood to panel each side flush.

The frame should comprise a head plate, sole plate, two upright studs and a central brace. Toe-nail these together and to the insides of the opening, making sure the frame is set back from the face of the wall to allow for the thickness of the skimmed wallboard.

Nail a panel of wallboard to each side of the frame, and to prevent the skim coat shrinking back from the edges, nail lengths of metal lath around the join. Apply a skim coat of finish and when the plaster has hardened, fit a length of new baseboard across the opening.

To fill the opening with bricks or concrete blocks, you must tie the new masonry to the old. The easiest method is to hammer 6in masonry nails half-way into the side of the opening to correspond with the mortar joints of alternate courses of the new bricks which will eventually be buried in the mortar.

Lay the bricks or blocks in the normal overlapping fashion and point all the mortar joints flush with the face of the masonry when finished.

Finally, apply floating and finish coats of plaster, using the surrounding original plaster as a thickness guide.

Wearing protective clothing, (especially the goggles), carefully cut away the plaster from within the lintel outline to expose the masonry below. Remove the bricks or blocks by cutting through their mortar joints and lifting them out. If any above the slot should drop, remove these and keep them for replacement later. Retain any whole bricks from the slot for possible reuse.

Lift the lintel into place, bedding it on mortar (3 parts soft sand: 1 part masonry cement) laid on the “bearings” at each end of the slot. It is best to get the help of an assistant with lifting the lintel, especially when lifting weights above the head. Make sure the lintel is level and, if necessary, pack it out below the ends with tiles or slates.

Finally, fill any spaces around the lintel with more mortar and replace any bricks or blocks that may have dropped out at the slot-cutting stage. If the wall is constructed of blocks, bring the lintel up to the height of the adjacent blocks by laying a course of bricks on top, and mortering them in place.

Leave the mortar to set for at least 24 hours, and preferably 48. Then remove the needle and wood supports. Fill the needle holes with brick offcuts and mortar. Lever off the baseboard and place it to one side for cutting down later.

Remove the plaster inside the outline of the opening to expose all the masonry below. Using a light sledge hammer and bolster chisel, cut this out by chiseling through the mortar joints, carefully working down the wall one course at a time. Because of the bonding pattern used, you will find that on alternate courses you will have to cut through bricks at the sides of the opening. Do this as you come to them. driving the chisel into their faces and levering them out from below to leave a straight edge to the opening. Remove all the bricks from the opening.

Trim off the masonry flush with a solid floor, or jus: below a wooden one. In the latter case, join the tv,-: floors by screwing battens to the joists then fit a piece of plywood or short pieces of floor-board on top neaten and close the gap.

The frame can be held in place with either galvanized metal ties mortared to the wall, or by screws and wall plugs. If ties are to be used, you need three per side. Cut recesses in the sides of the opening for the ties. If you intend screwing the frame to the wall, drill screw clearance holes in it and offer it up so these can be marked on the wall. Drill and plug the holes.

Set the frame in place, packing out the sides as necessary with wood offcuts to set them vertical. Then either fill the tie recesses with mortar and brick offcuts or insert the screws.

Fill in the gaps round the frame with more mortar and offcuts and trowel a thin layer of mortar over any exposed masonry at the sides and top before refinishing the plaster.

Finally, nail lengths of molding around the frame, mitering the corners, and trim and refit the base boards to the base of the wall.

As with all jobs of this type, making a new doorway requires careful planning. You should also check the requirements of your local building code.

A lintel must be chosen to match the type of wall being cut into and you must select a position for the door that, if possible, will not interfere with existing cable and pipe runs and which should be at least 18in from any corner.

It is possible to buy doors and ready-made frames in a range of standard sizes, and unless you are making the frame, it is best to buy the door and frame first, making the opening to fit it. Make sure its height leaves enough of the wall above the opening for fitting the lintel and the temporary wood supports.

With a masonry wall, you must provide temporary support for the wall above the opening and the load it carries while you cut out a slot for the lintel. If the wall supports the joists of the ceiling above, you must also make sure you support the ceiling on both sides of the wall as well.

Support the wall with 6ft lengths of 2 x 4in wood called “needles” — on top of adjustable metal props, which work like an automobile jack (you can rent these), spaced at 3ft intervals. With a normal sized doorway, you would need only one set centrally above the opening.

To support the ceiling, lengths of 4 x 12in wood are used across the tops of more props. None of the props should be more than 2ft from the wall, and if they are to stand on a wood floor, the feet should be placed on another length of 2 x 4in wood to spread the load.

Before marking out the doorway on the wall, use a bricklayer’s chisel and hammer to remove patches of plaster roughly where the edges and top of the opening will be. This will allow you to adjust fairly accurately the position of the opening to coincide with the mortar joints, in order to reduce the number of bricks you have to cut through.

Measure up the door frame, adding 2in to its width and lin to its height to allow for positioning. Using these dimensions, draw an outline of the opening on the wall. Then measure up the lintel — which should be at least l ft wider than the opening — and add a further 2in to its width for fitting. Draw the outline of the lintel on the wall above the door opening.

Finally, draw the outline of the wood needle centrally above the needle outline. Repeat the outlines on the other side of the wall.

Cut the hole for the needle with a hammer and bricklayer’s chisel. Slide the needle through so it protrudes equally on both sides of the wall and fit the props beneath it, tightening them to take the load. Both props must be adjusted simultaneously to ensure even support. Then fit the ceiling supports.

Plaster is an excellent and inexpensive material for giving a smooth, hard surface to an internal wall so that it is ready for painting or wallpapering.

There are many types of plaster, but they can be divided into two basic types: gypsum-based and cement-based. The former are used solely for indoor work, whereas the latter are mainly used outdoors for rendering walls. Cement- based plasters do have a use indoors. however, and that is to finish external walls that might be subject to damp penetration; damp will attack a gypsum plaster and cause it to crumble.

Modern plasters come premixed with lightweight fillers such as perlite or vermiculite, which give a higher degree of thermal insulation and fire resistance and should be mixed with clean water.

Plaster is normally applied to the wall in two layers. The first, called a “floating” coat, is intended to even out the irregularities in the wall surface, so it is kept fairly thick — about 3/sin being usual. The second, finishing coat is spread much thinner Ysin or so — and carefully toweled off to a smooth finish.

Different types of building materials absorb water at different rates and if too much water is absorbed from the fresh plaster, it will dry too quickly and crack.

For example, bricks and lightweight building blocks absorb water quickly and are termed high suction surfaces. On the other hand, materials such as concrete and gypsum board do not absorb water that quickly and are termed low suction. You must choose a plaster to match the surface; but if in doubt, the best thing to do is coat the entire wall with a bonding agent which will make a low suction surface.

Browning plaster should be used for the floating coat on high suction surfaces and Bonding plaster on low suction surfaces. Finish plaster can be used for the finishing coat in both cases.

Only buy plaster as you need it since it has a limited shelf life. A 22lb bag of Browning or Bonding plaster should cover an area of about 1.8yd2 at a depth of 3/sin. The same quantity of Finish plaster, spread thinly, should cover an area about 6yd2.

In addition to a couple of clean buckets and a long level, you will need some special plastering tools: a spot board about 3ft square and supported on trestles or an old table to hold the mixed plaster while you work; a hawk for carrying small quantities of plaster to the wall; a rectangular metal plasterer’s trowel: a wooden float for producing flat surfaces (with a few nails knocked into the end it can double as a “scratcher” for scoring the floating coat before applying the finishing coat): and a 5ft length of 1 x 3in planed wood for leveling the plaster surface.

Cleanliness is essential when mixing plaster. since any dirt present in the mix will affect the drying time. Always use clean tap water for mixing and have a separate bucket of water for cleaning the tools as you work.

Mix the plaster and water in equal volumes in a clean bucket, adding the plaster to the water by sprinkling it on top and breaking up any lumps between your fingers. When the water has soaked into all the plaster, use a thick piece of wood to stir the plaster into a smooth consistency, (Finish plaster should resemble runny ice-cream). and make sure there are no lumps.

Wet the spot board and turn out the plaster on to it, kneading it with the trowel. If the mix appears too wet, sprinkle on a little more plaster and mix in with the trowel.

The idea of an architrave is to hide the join between a door or window frame or lining and the surrounding plaster

A loose architrave can be nailed back in place to the door frame, or even screwed to the surrounding masonry if you drill right through it with a masonry bit and insert wall- plugs to take the screws. But removal and fixing are both easier than for skirting, so replacement is usually the sensible alternative to major repairs. You just lever the existing architrave off, and nail the new one on.

On a brick or block wall, you usually nail through the molding’s inner edge and into the doorframe, lining or ‘wrought grounds’ with 25 mm (1 in) oval nails; lost-head nails or panel pins can also be used. But if necessary you can nail through the middle of the molding and into the wall itself, using cut nails for medium-hard blocks if you like, and masonry nails for bricks and hard blocks. If you find that there are rough (concealed) grounds between the plaster and the frame or lining, then nail into those. On a stud wall, nail into the studs.

At the bottom, the upright pieces butt against the floor and the ends of the skirting. At the_ top the corners are mitred. A good idea is to start by cutting off three pieces of molding which are manageable but still slightly too long. Then you can mark off the heights of the two upright ones (which may of course differ a bit, depending on whether the floor is flat or level), mitre their top ends and fix them loosely to the wall.

This makes it easy to mark off the exact length of the top piece. Mitre its ends, position it, and make any adjustments – by moving the uprights slightly, and even shaving the mitred ends with a sharp chisel or block plane if necessary. Then nail all three pieces finally in place, and pin the mitres from the top as for skirting boards.

When mitring, always make quite sure you’re cutting the right way round. That sounds silly, but you’ll find it’s all too easy to waste whole pieces by mistake

Failing that, a hacksaw should do the job.

In certain places — eg, the backs of alcoves — the skirting board is held in position by the two pieces at right angles to it. So, unless you remove at least one of those first, sawing the board out is your only option. A flooring saw may work. Otherwise drill a series of holes in line dOwn the face of the skirting, and use a chisel to chop out the waste between the holes so you can prise out the two ends of the board. Pipework and other obstacles sometimes force the same solution.

If a length of skirting refuses to come away completely, you may still be able to make sawing easier by levering enough of it out to push timber wedges behind it. In all cases, it’s best to saw at an angle of 45° across the thickness. If you’re just removing a section, cut the new piece to the same angle when you come to fix that in place.

Always use 45° cuts, rather than butt joins, if you have to make up a long piece from two shorter ones. They’ll be less conspicuous, especially if you site the join near an out-of- the-way corner.