Plastering Techniques

Filed Under: Do it yourself, Home repair, Remodeling    by: ITC

Plaster is an excellent and inexpensive material for giving a smooth, hard surface to an internal wall so that it is ready for painting or wallpapering.

There are many types of plaster, but they can be divided into two basic types: gypsum-based and cement-based. The former are used solely for indoor work, whereas the latter are mainly used outdoors for rendering walls. Cement- based plasters do have a use indoors. however, and that is to finish external walls that might be subject to damp penetration; damp will attack a gypsum plaster and cause it to crumble.

Modern plasters come premixed with lightweight fillers such as perlite or vermiculite, which give a higher degree of thermal insulation and fire resistance and should be mixed with clean water.

Plaster is normally applied to the wall in two layers. The first, called a “floating” coat, is intended to even out the irregularities in the wall surface, so it is kept fairly thick — about 3/sin being usual. The second, finishing coat is spread much thinner Ysin or so — and carefully toweled off to a smooth finish.

Different types of building materials absorb water at different rates and if too much water is absorbed from the fresh plaster, it will dry too quickly and crack.

For example, bricks and lightweight building blocks absorb water quickly and are termed high suction surfaces. On the other hand, materials such as concrete and gypsum board do not absorb water that quickly and are termed low suction. You must choose a plaster to match the surface; but if in doubt, the best thing to do is coat the entire wall with a bonding agent which will make a low suction surface.

Browning plaster should be used for the floating coat on high suction surfaces and Bonding plaster on low suction surfaces. Finish plaster can be used for the finishing coat in both cases.

Only buy plaster as you need it since it has a limited shelf life. A 22lb bag of Browning or Bonding plaster should cover an area of about 1.8yd2 at a depth of 3/sin. The same quantity of Finish plaster, spread thinly, should cover an area about 6yd2.

In addition to a couple of clean buckets and a long level, you will need some special plastering tools: a spot board about 3ft square and supported on trestles or an old table to hold the mixed plaster while you work; a hawk for carrying small quantities of plaster to the wall; a rectangular metal plasterer’s trowel: a wooden float for producing flat surfaces (with a few nails knocked into the end it can double as a “scratcher” for scoring the floating coat before applying the finishing coat): and a 5ft length of 1 x 3in planed wood for leveling the plaster surface.

Cleanliness is essential when mixing plaster. since any dirt present in the mix will affect the drying time. Always use clean tap water for mixing and have a separate bucket of water for cleaning the tools as you work.

Mix the plaster and water in equal volumes in a clean bucket, adding the plaster to the water by sprinkling it on top and breaking up any lumps between your fingers. When the water has soaked into all the plaster, use a thick piece of wood to stir the plaster into a smooth consistency, (Finish plaster should resemble runny ice-cream). and make sure there are no lumps.

Wet the spot board and turn out the plaster on to it, kneading it with the trowel. If the mix appears too wet, sprinkle on a little more plaster and mix in with the trowel.

Plaster-Boarding

Filed Under: Do it yourself, Home repair, Remodeling    by: ITC

Plasterboard is a sandwich of gypsum plaster held between two layers of thick paper. You can plaster lower it, paint or paper it to match other walls. It is ideal for cladding a timber framed partition, the panels being simply nailed in place.

Always handle pasterboard carefully; it is easily broken. If you intend plasteringit, fit the gray side outermost, but if you want to paint or paper over it leave the ivory colored side showing.

Fix all the full size panels to the framework first then the smaller pieces, completing one side at a time. If the partition does not span the rppm filly, work from the outer end towards the wall.

To cut plasterboard, use a sharp knife and steel straightedge; after cutting through one side, stand the board on edge and snap it back to break the plaster. Cut through the remaining paper layer. For right-angle cuts mark both sides of the panel and cut through from both sides. Trim full panels to measure about 1 in less than the floor-to-ceiling height; this will allow you to push them up tight against the ceiling with a “footlifter” before nailing.

Fix the board to the frame, using 11/4in galvanized plasterboard nails or screws, spacing them at 6in intervals and working outwards from the center of the panel. Keep the fixings at least 11/2in from the edge of the panel to prevent them from breaking the edge. Drive the nails or screws in so that their heads come just below the surface. This is enough to allow for a thin skim of filler.

To fill the joints, apply a layer of proprietary joint filler then press in a length of paper or fiberglass jointing tape. Apply more filler up to the level of the surrounding plasterboard, feathering the edges with a damp sponge. When dry, apply one or two thin layers of joint finish, again feathering the edges.