Indy Total Construction

A problem with taps and baths is staining just below the taps. This tends to be at its worst in hard water areas and, so far, nobody has come up with a really effective way of removing these stains once they’ve formed. As always, prevention is better than cure, so you should make sure that the staining doesn’t build up in the first place.

Dripping taps and shower roses should be repaired as soon as possible, and if they’re old enough to introduce the additional problem of rust staining you should consider having them replaced.

You can work to minimize the build-up of stains by wiping out the bath immediately after use and cleaning it regularly with a proprietary cleaner. However, if the bath surface has got to the point where even the most thorough cleaning cannot help, then you’ll have to think about giving it a facelift.

Bath enamel – a hard-wearing version of ordinary enamel paint was originally used for covering up badly stained enameled surfaces.

However, over the years this has acquired an unfortunate reputation for failure not only is it unable to withstand the sort of treatment it gets in a bath, but also extreme care is required during both preparation and application in order to produce acceptable and lasting results. It is still available. but usually only in white. and it is worth considering only if you want to touch up the scratched surface of a cooker, fridge or washing machine.

For baths and other bathroom fittings. a recent development has proved to be a better option. This is an epoxy resin coating that will provide a very hard, heat-resistant and chemical-resistant finish on most of the non-porous surfaces to be found in the bathroom. It comes in a number of different colors that will match the coloring of modern bathroom fittings with the excepts of white. It cannot be used on plastics or surfaces that have already been painted.

The only possible disadvantage is that can sometimes work out a bit expensive, though it will obviously be considerably cheaper than buying a new bathroom suite.

Whether or not you’ve had to pause in order to repair a sash or to repaint everything, you’re now ready to carry on and fit new sash cords.

The first step is to remove the weights. To get at them, you have to take out the one or two pieces of wood covering each weight compartment — the pocket pieces. These are usually just a push fit, and you pry them out with an old chisel or screwdriver; in somecases, – however, there’s also a retaining screw. Lift out each weight, untie the cord from it, and attach it to the free end of the string, making a complete loop. If there’s rust on the weight, you can rub it off with abrasive paper at this stage. but there’s no need to paint it.

You can buy new sash cord from almost any builder’s merchant or hardware store, but ask for it by name — doesn’t just use any old cord. To fit the new cord, untie the loop of string. tic the cord to it, and use it to thread the cord over the pulley and down into the weight compartment. Then tie the cord to the weight with a strong knot. At this stage don’t try cutting the cord to the correct length — leave it too long.

Most sashes have a groove, near the top of each side, in which the cord is fixed with small galvanized round-head nails. Either nails the cord into the groove and trims off the excess, or marks the groove length on the frame and trims the cord to the mark.

Whichever you do, the weight should hang 50mm (2in) above the base of its compartment when the sash is at the top of the frame. It’s the same for each sash. Note that the cord shouldn’t be fixed right to the top of the groove, or the sash won’t run all the way up. The topmost nail should be as far down from the top as the top of the pulley is from the top of the frame opening.

After fixing the cords at both sides of the outer sash, replace the parting bead. Then repeat the whole process for the inner sash, and lastly replace it and the staff bead in position. When fixing the beads. make sure the sashes have room to slide free.

Walls are the first thing anyone entering your home will see. They should be kept clean and in good repair.

There are many ways to finish walls. Probably the most common is painting. Paint preserves and beautifies many objects. It protects metal from rust, wood from mildew and plastics from sun damage. Paint also makes them easier to clean.

There are many types of wall coverings. Paper, plastics, and fabrics are some. Wall coverings can be prepasted and pretrimmed. Some are washable; and some are even treated for easy removal at a later date.

Paneling is easy to care for, and there are many different types to choose from.

Whatever type of wall finish you use, the job should be clean and neat. You should also know some of the chemistry of the materials and surfaces you are working with—what will mix and what may explode.

Painters will always have work. Even if the perfect paint—one that never wears out—is discovered, there will always be someone who doesn’t like the color!

Drywall is soft. It is best held in place with large headed drywall nails, screws or staples.

To prevent nails and seams from showing, nails are dented into the walls. The dents are then filled with drywall cement. Then you cover the seams with drywall tape and plaster over with drywall cement.

Finishing drywall seams. Apply compound over the seams and nail impressions. Work the tape into this compound. Smooth over, allow to dry, and sand.

In many modern houses, interiors are finished with drywall. Drywall normally comes in sheets, 4′ x 8′, 4′ x 10′, or 4′ x 12′. It is usually 5/16, 3/8, 1/2 or 5/8 inch thick. The most common size is 3/8 inch thick 4′ x 8′.

Drywall sheets are nailed to the house joists with large headed nails, screws, or staples. Nails are driven so that a small dent is made in the drywall. This depression is then filled with a type of cement and covered over with tape

There are three basic ways to finish drywall:

• Painting

• Wallpapering

• Paneling

You may apply paint directly to drywall. New drywall usually takes two coats: one to seal it and one to present an even, finished surface.

Wallpaper is becoming popular again. It comes in rolls and is applied directly to the drywall. Before it will stick, the drywall must be prepared with a glue-like coating of sizing. The trick in applying wallpaper is to avoid bubbles and match the edges and the pattern precisely.

Paneling is glued or nailed directly onto the drywall. Panels may be veneer, wallboard, imitation masonry, or some other material.

Moldings and baseboards finish off walls and ceilings. In older homes they are always made of wood. Most new molding and baseboard is made of synthetic materials which are more flexible and less likely to crack when nailed into place.