Building a Stud Partition

Filed Under: Do it yourself, Home repair, Remodeling    by: ITC

The easiest form of partition to build is the wood frame variety — it is ideal for dividing one bedroom into two, making an extra powder room or bathroom, or splitting a dining area from a kitchen or living room. The wood frame is simply nailed together and faced with drywall on each side; it is easily adapted for doorways, pass through or windows. Being essentially hollow, it can also be used to conceal electrical wiring and water pipes.

The framework comprises a number of uprights called “studs” fitted between lengths of wood spanning the width of the ceiling and floor. These are called the “head plate” and “sole plate” respectively. Short horizontal lengths of wood are fixed between the uprights to brace them and support the cladding. In most cases 2 x 3in rough sawn softwood is ideal for the studs and bracing, with 11/2 x 3in for the head and sole plates. If the partition is to carry a lot of weight such as shelves or cupboards, a larger size should be used, say 2 x 4in.

Planning the partition

Deciding where to put the partition is the first thing to do so that you end up with two usable rooms. If possible arrange things so that each new room gets the benefit of a window, but do not be tempted to set the partition so that it divides a window in two. Not only does this look dreadful, but in some cases it is also illegal. If you cannot provide a window for each room, glaze the upper portion of the partition so that you can “borrow” some natural light from the room with the window. Similarly, if you cannot provide an opening window for each new room, you will be required to install a form of mechanical ventilation.

Important considerations are the layouts of floor and ceiling joists since the head and sole plates will be attached to these. Ideally, the partition should run at right angles to the joists so that its weight is spread across them. If this is not possible, it must be directly above a joist. With a solid floor, there is no problem.

If the head plate does not span the ceiling joists and does not come below a single joist because the ceiling joists do not line up with the floor joists, you should nail lengths of 2in sq blocking between the ceiling joists and attach the head plate to these.

Before you begin work, check under the floor and above the ceiling for any cables or pipes that might be damaged by nails or screws. It is also a good idea to check with your local Building Code before carrying out any structural work.

Erecting the framework by cutting the head and sole plates to length; whenever possible buy wood long enough so that you can span the room with one piece. Nail the sole plate to the joists through the floorboards using 4in long common nails or fix it to a concrete floor with 4in long No.10 woodscrews and wall plugs or with masonry anchors or masonry nails. Screw the head plate to the ceiling joists.

Cut the studs for each end of the partition, leaving them a fraction over-length so that they will be a tight fit between the head and sole plates, and screw them to the wall. Use 4in long No.10 screw and wall plugs.

Then mark off the positions of the other studs along the sole plate, making sure their centers are 16in or no more than 24in apart. They should be positioned so that the edges of the cladding material will meet along their center lines (standard sheets of drywall are 4ft wide). If the partition is to have a door in it, the stud positions on each side of the opening must be adjusted to allow for the door width and the thickness of the lining.

Measure and cut each stud individually as there is no guarantee that head and sole plates will be parallel.

Set each stud in place, making sure it is vertical with a spirit level, and fix it by driving 3 or 4in common nails at an angle through the side of the stud into the head and sole plate (known as toe-nails).

Dividing Spaces in Your Home

Filed Under: Do it yourself, Home repair, Remodeling    by: ITC

Partitions can be used in most homes to make best use of available space, turning large or awkwardly- shaped rooms into more manageable accommodation.

The large, L-shaped room is common to many homes, yet it is not the most convenient of shapes to furnish or heat. By building a partition with an access door across one of the legs you can produce two smaller, rectangular rooms which are much cozier and more easily heated.

Long, narrow rooms also produce their own particular problems, such as giving the impression of being like tunnels or causing difficulties in positioning furniture. The tendency is to put everything around the walls, leaving a large bare area in the center of the room.

By building a partition that spans, say, only half of the room’s width, you can create two distinct areas (for living and dining perhaps) without completely losing the feeling of being in one large room.

Furniture can then be grouped more effectively into sitting arrangements and dining areas. You can achieve the same effect by building a waist-high partition across the room, but in this case there would be much more of an open-plan feel to the room. Such a partition would also provide some useful shelf space along the top, or for a tier of shelves above.

Obviously, if you are using a partition to make two rooms out of one, you will have to arrange access to the new room. The easiest way is to build a door in the partition.

However, this means that you must walk through one room to reach the other and that might not always be convenient, especially if the rooms are used as bedrooms. To overcome this problem you can either make a new doorway through one of the original walls of the room or build a second partition at right angles to the first to form a small lobby, from which both rooms can be entered separately and maintain a sense of privacy.

A bathroom formed by partitioning off part of a larger room. The confined space is visually enlarged by the overall tiling of the walls and bath platform, and light is admitted through a glass block wall.

An important point to consider when partitioning a room is the availability of daylight in both new rooms. You may find that the only suitable position for the partition means that one room has no window at all. In this situation, you can provide a fair degree of natural light by incorporating panes of glass (clear or frosted depending on the purpose of the room) along the top of the partition. You could even include a glass door.

Partitions can be very useful for creating storage. By building what is effectively a false wall across the end of a room, you can use the space between it and the original wall for inset shelving, cabinets and even walk-in closets. This can be very handy if there is a small room next to a large one, since by cutting an opening in the original dividing wall and arranging the internal divisions of the storage space partition at right angles to the first to form a small lobby, from which both rooms can be entered separately and maintain a sense of privacy.

An important point to consider when partitioning a room is the availability of daylight in both new rooms. You may find that the only suitable position for the partition means that one room has no window at all. In this situation, you can provide a fair degree of natural light by incorporating panes of glass (clear or frosted depending on the purpose of the room) along the top of the partition. You could even include a glass door.

Partitions can be very useful for creating storage. By building what is effectively a false wall across the end of a room, you can use the space between it and the original wall for inset shelving, cabinets and even walk-in closets. This can be very handy if there is a small room next to a large one, since by cutting an opening in the original dividing wall and arranging the internal divisions of the storage space carefully, you will provide a storage facility for both rooms.