Indy Total Construction

When you want to get into your attic there is no reason why you should not use an ordinary ladder, provided it is secured to the opening in some way – by hooks and eyes perhaps, but whatever you do, never use a pair of step ladders. In trying to climb out of the attic and groping for the top of the steps with your foot, you could easily knock them over, leaving you stranded, or worse you might fall with the ladder causing physical injury.

One drawback to using a normal ladder is that you will need somewhere to store it and you will have to go to the trouble of digging it out of storage every time you want to get into the roof space — or it may be in use elsewhere in the house.

A much more satisfactory solution to the problem of climbing into your attic is the proprietary extendable attic ladder. This sits just above the trapdoor on hinges or pivots screwed to the inside or top of the opening frame and can be pulled down whenever you need it. Such a ladder, with its own built-in storage, makes your attic much more usable and accessible.

Purpose-made attic ladders are usually produced in aluminum with 2 or Sin wide treads. Most have two or three sliding sections with a safety catch that must be released before they can be extended. Some are linked to the trapdoor by a special bracket so that they come immediately to hand when you open it up.

When closed, the ladder lies across the tops of the joists next to the trapdoor, but it swings upwards over the opening before it can be pulled down, so it is essential that there is enough height above the opening for this.

Another important factor is the size of the opening itself which must be large enough to allow the ladder to pass through. This is not usually a problem if you are making a new opening, but if you want to fit the ladder to an existing opening, you will have to take some careful measurements. You will also need to know the distance from the floor of the attic (not the ceiling) to the floor of the room below.

For extremely limited attic space, there is a concertina attic ladder that folds up compactly rather than sliding.

Attic ladders can be simple or complex in design with risers and balustrades just like a proper staircase. Most come with some form of automatic trapdoor catch operated by relatively light finger-tip pressure on the door itself.

Obviously, the method of installing an attic ladder varies from one make and model to another, but usually it is quite a simple procedure. Often all that is necessary is to screw the hinges or pivots to the framework of the opening (on the same side as the trapdoor hinges) and fit the automatic catch to the other side of the opening. There may also be travel stops to adjust on the ladder and a bracket to fit to the trapdoor to hold the ladder so that it is easily reached.

To put a doorway in a stud partition, first expose the framework below the skin of the partition. Find the stud positions on each side of the proposed opening by tapping the surface and probing with a bradawl. Draw in the stud positions on the surface and another line between them to mark the height of the door frame plus an allowance for the wood lintel.

Cut along this outline with a keyhole saw continuing the cut through the skin across the top of any studs or bracing you come across. Lever off the skin to expose the framework and the back of the other skin. Remove the latter in the same way.

Cut out all the framework within the opening and then make up two short “trimmer” studs to support the lintel. Nail the trimmer studs to the original studs on each side of the opening and the lintel to the tops of the trimmer studs. Nail through the lintel into the base of any cut stud.

If the door frame is narrower than the distance between the trimmer studs, fit an intermediate between the lintel and sole plate, linking it with short braces to one of the trimmer studs.

Cut out the section of sole plate across the bottom of the opening and fit the door frame. Finish the partition by nailing on gypsum- board and applying a skim coat of plaster over the top.

A hatchway between a kitchen and dining room can be extremely useful, and you may wish to consider installing one should you have to block off a redundant doorway, or to suit other remodeling plans. Plan its position carefully so that it coincides with a work surface in the kitchen and something like a worktop or small table in the dining room so that there will be somewhere to place dishes and plates, for example.

The method for making a pass-through is basically the same as that for making a doorway, except that the opening is not continued to the floor. In a wood framed partition, a wood sill piece is needed between the studs on each side of the opening.

The pass-through can be left open with plastered edges and a wood sill, screwed across the bottom or a wooden lining frame can be fitted to take hinged or sliding doors, or some form of roller blind to give the maximum amount of privacy, and also to prevent cooking smells, for example, from drifting through.

As with all jobs of this type, making a new doorway requires careful planning. You should also check the requirements of your local building code.

A lintel must be chosen to match the type of wall being cut into and you must select a position for the door that, if possible, will not interfere with existing cable and pipe runs and which should be at least 18in from any corner.

It is possible to buy doors and ready-made frames in a range of standard sizes, and unless you are making the frame, it is best to buy the door and frame first, making the opening to fit it. Make sure its height leaves enough of the wall above the opening for fitting the lintel and the temporary wood supports.

With a masonry wall, you must provide temporary support for the wall above the opening and the load it carries while you cut out a slot for the lintel. If the wall supports the joists of the ceiling above, you must also make sure you support the ceiling on both sides of the wall as well.

Support the wall with 6ft lengths of 2 x 4in wood called “needles” — on top of adjustable metal props, which work like an automobile jack (you can rent these), spaced at 3ft intervals. With a normal sized doorway, you would need only one set centrally above the opening.

To support the ceiling, lengths of 4 x 12in wood are used across the tops of more props. None of the props should be more than 2ft from the wall, and if they are to stand on a wood floor, the feet should be placed on another length of 2 x 4in wood to spread the load.

Before marking out the doorway on the wall, use a bricklayer’s chisel and hammer to remove patches of plaster roughly where the edges and top of the opening will be. This will allow you to adjust fairly accurately the position of the opening to coincide with the mortar joints, in order to reduce the number of bricks you have to cut through.

Measure up the door frame, adding 2in to its width and lin to its height to allow for positioning. Using these dimensions, draw an outline of the opening on the wall. Then measure up the lintel — which should be at least l ft wider than the opening — and add a further 2in to its width for fitting. Draw the outline of the lintel on the wall above the door opening.

Finally, draw the outline of the wood needle centrally above the needle outline. Repeat the outlines on the other side of the wall.

Cut the hole for the needle with a hammer and bricklayer’s chisel. Slide the needle through so it protrudes equally on both sides of the wall and fit the props beneath it, tightening them to take the load. Both props must be adjusted simultaneously to ensure even support. Then fit the ceiling supports.